跳至主要内容

Why should we pay attention to the cylinder when buying a CNC bending machine

 Why should we pay attention to the cylinder when buying a CNC bending machine


The cylinder is used to hold hydraulic oil, and the CNC bending machine is a kind of machine for bending sheet metal. When we use the CNC bending machine to bend the material, we must bend in the middle section. If we are bending on one side, then when the cylinder on one side touches the workpiece, the cylinder on the other side will continue downward until it touches the lower die, the two cylinders begin to pressurize. If the cylinder is working like this, one side high and the other side low, the cylinder of the CNC bending machine will soon be damaged and leak oil. Secondly, try not to choose a two-cylinder CNC bending machine, because the working life of such a CNC bending machine is too short. When the workpiece is in the middle of the CNC bending machine and the cylinder is on both sides, the bending of the slider is affirmative; in addition, due to the reaction force generated by the inclination of the slider, the center of the slider protrudes outward, resulting the Inaccurate bending.

CNC bending machine provider

Since the two-cylinder CNC bending machine is not good, the three-cylinder CNC bending machine is better. The third cylinder is in the middle and the force point is directly in place. The slider will not deform or protrude, which is fully guaranteed The accuracy of bending and also can extend the service life of the equipment.

In addition to the proper selection of the CNC bending machine itself, some important parts of it must also be adjusted reasonably, such as the CNC bending machine presser foot, which is used to press the steel plate during bending. If its seal leaks, It will result in insufficient pressure of the presser foot, which will cause the steel plate to buckle up and some damages such as shear blade chipping and knife jamming.

In this regard, we must pay attention to check the presser foot of the CNC bending machine to prevent the leaking of the seal. If the problem has occurred, it is necessary to replace the seal in time to ensure that the press foot of the CNC bending machine has enough pressure to press the steel plate, which provides a good foundation for the smooth completion of the bending work.

two-cylinder CNC bending machine

The above is the reason why you need to look at the specific content of the cylinder when buying a CNC bending machine. Hope it will help you. For more information about CNC bending machines, please see the previous content of our company. If you have any questions, please contact our staff and we will answer you one by one.


Product details: CNC bender

标签：

评论

发表评论

此博客中的热门博文

Dingya Crane Provides High-configuration Metallurgical Cranes

  Metallurgical cranes refer to   bridge-type cranes   used in metallurgy, casting and other places for lifting molten metal. They are also called metallurgical cranes. Nowadays, many small cast iron, cast steel and other metal smelting companies are using ordinary   single-girder cranes , but due to their design limitations, there are obvious hidden dangers, and the service life is greatly reduced. It is safer to switch to metallurgical driving as required. Compared with cranes used by general enterprises,   Dingya metallurgical cranes   have the characteristics of frequent use, harsh environment, high security performance and high automation. Starting from the transmission scheme, to the selection of components and wires, as well as component layout, wiring methods, and even electrical the sealing, cooling and other issues of the room and cabinet have been comprehensively considered and designed. Since there are many types of metallurgical cranes and each...
发表评论
阅读全文

Classification of diamond drill bits

  1. surface set diamond bit Explanation: A kind of diamond drill bit . The steel cylindrical bit body has a wire buckle on the upper part and a sintered drill head body on the lower part. The diamond particles are encrusted on the surface of the drill head body. The outer diameter of the carcass is slightly larger than the diameter of the steel body and the inner diameter is slightly smaller than the diameter of the steel body. There are grooves inside, outside and at the bottom that allow water to pass through the carcass. During drilling, washing fluid is used to carry away rock powder and cool the bit. Diamond-impregnated bits are all encrusted with natural diamonds and are therefore expensive, so they are only used in hard formations that are particularly difficult to drill. Diamond-impregnated drill bit is more commonly used in oil drilling. 2. impregnated diamond bit Explanation: A kind of diamond drill bit. A drill bit whose head body is uniformly encrusted...
发表评论
阅读全文

Diamond Polishing Pad

  Diamond polishing pad , also known as diamond polishing pad , is a flexible processing tool made of diamond as abrasive, combined with composite materials, with Velcro cloth on the back, glued to the joint of the grinding machine, used for grinding, stone, ceramic, glass, floor tile and other materials for special-shaped processing, suitable for stone polishing, line chamfering, curved plate and special-shaped stone processing. It can also be used for the special-shaped processing, repair and renovation of marble, concrete, cement floor, terrazzo, microcrystalline glass, artificial stone, floor tile, glazed tile and vitrified brick. It is an ideal stone grinding tool with strong grinding force, good durability, good softness, clarity and gloss. The whole process is divided into rough grinding, fine grinding, fine grinding and polishing four stages. The gloss is over 90°. Use 1, used for artificial stone, granite and marble stone processing, with a complete stand...
发表评论
阅读全文