Industrial industry blog posts

  1000L Ribbon Mixer With Weighing System  is used to mix various powders and can weigh the mixed materials at the same time.   Technical parameter of 1000L Ribbon Mixer With Weighing System: 1. total volume is 1000 Liters 2. loading volume: 400-600 Liters per batch 3. mixing motor:15KW 4. customized motor: Explosion-proof motor to protect operators working in a flammable and explosive environment 5. mixing speed: 42RPM 6. weighing system: installing load cell to weigh the ribbon mixer 7. electric control: PLC control  8. dimension: 3100*950*1600mm 9. weight: 1200kg   Features of 1000L Ribbon Mixer With Weighing System: 1. horizontal ribbon mixer can make a homogeneous mixing effect. 2. weighing sytem can weigh each material separately before mixing. 3. a relatively faster mixing speed than other mixers. 4. explosion proof motor is customized by customer. 5. PLC control is asked by customer for easy operation and high accurate control.  

Gel Clot Lyophilized Amebocyte Lysate (TAL) Single Test in Ampoule 1. Product Information Bioendo’s Lyophilized Amebocyte Lysate (TAL) reagent is the product manufactured with amebocyte from blood of Tachypleus tridentatus. After rehydrating TAL reagent with Water for Becterial Endotoxin Test, sample could be added directly to the ampoule. Then incubate solution at 37ºC±1ºC for 60±2 minutes. Take each tube in turn directly from the incubator, and invert it through about 180º in one smooth motion. If a firm gel has formed that remains in place upon inversion, it means the sample contains endotoxin. None extra endotoxin-free tube is needed when do endotoxin detection with our Gel Clot Lyophilized Amebocyte Lysate (TAL) Single Test in Ampoule. 2. Product Parameter Sensitivity Range: 0.03, 0.06, 0.125, 0.25, 0.5, 1.0, 2.0 EU/ml Single Test per Ampoule Positive or Negative Results Require Sample Volume: 0.1ml per Test 3. Product Feature and Application Single step endotoxin detection witho...

Winter is coming, is your fireplace ready to turn on? Have you done a few tasks before starting up? Step1 Water, electricity, gas and pipeline inspection 1. Confirm that the pipeline valve is open, and pay attention to whether the pipeline system is dripping or leaking; ※When installing a heating system with a radiator, pay attention to the temperature control valve on the radiator. ※When installing a floor heating system, you need to pay attention to the collector and distributor. First, open the valve of the main water supply pipeline of the water divider. When the temperature of the hot water gradually rises and is injected into the pipeline to circulate, check whether the connection of the water divider is abnormal, and then gradually open the branch valves of the water divider to check the operation status. 2. Confirm that the power is on; 3. Confirm that the gas valve is open, and check the sealing performance of the natural gas pipeline and all joints at the same time, whether ...

Can laser cutting machine cut galvanized sheet? Galvanized sheet is a relatively common material used in manufacturing. Galvanized sheet is the steel sheet coated with a layer of metallic zinc on the surface which can prevent corrosion and extend its service life. So is this material suitable for laser cutting machines ? Generally for galvanized sheets, laser cutting machines can cut easily. Most organic and inorganic materials can be used. Various metal materials commonly used in industrial manufacturing systems are almost cut regardless of their hardness. Copper, aluminum and their alloy plates are all no problem. In the process of processing galvanized sheet, auxiliary gas needs to be added. The purity and pressure of auxiliary gas directly affect the quality of the cut sheet section. The oxygen purity for cutting should be above 99.6%. When the purity of the oxygen used for cutting is higher, the better of the roughness and quality for the section of galvanized sheet will be, of co...

[up to standard] GB/T12704 ASTME96 JISL1099 BS7209, etc. "Method for The Determination of Moisture Permeability of Fabrics - Moisture Permeability Cup method/Method A" Standard Test Methods for Water Vapor Transmission of Materials (ASTM E96-00) British standard BS7209-1990 moisture absorption method [Use Environment] 1. Ambient temperature: 15~30℃ 2. Relative humidity: less than 80% RH 3. Power supply: 220V± 5% 50Hz 4. The instrument shall be grounded 5. The instrument should be placed at least 30cm away from obstacles. Main USES: The moisture permeability tester is used for testing the moisture permeability of various coated fabrics, composite fabrics, composite films, plastic films, exchange films and other materials, and is often used for testing medical fabrics. Technical indexes of moisture permeability tester: 1. Adjustable temperature control accuracy: 20 ~ 50℃±0.1℃; 2. Adjustable humidity relative humidity: 40 ~ 95%±1%RH 3. Standard test temperature and humidity: 30...

PTFE tape with a chemical name polytetrafluoroethylene, which is commonly used in plumbing area plain white teflon tape, and gas pipelines also have special teflon tape. In fact, the main raw material is polytetrafluoroethylene, only the technical processes are not the same. Most of the time, it is used as a water pipe installation aids for pipe connections, enhanced sealing between duct connection. Which mahcine could produce PTFE tape? Yes, it is PTFE teflon tape CNC stretch slitting machine .D&S PTFE teflon tape CNC stretch slitting machine, high efficiency, low energy consumption, high output.

  100L Horizontal Ribbon Mixer With Liquid Spray System Is Used to Mix Detergent Powder And Water Together.   100L Horizontal Ribbon Mixer is equipped with liquid spray system. 1. Total Volume of the mixing tank is 100L. 2. Loading volume is about 40-60 Liters per batch. 3. Loading capacity is about 40-60 kgs per batch if the average bulk density of the mixing materials is 1.0 g/cm3. 4. Mixing motor is 3kw. because the bulk density is not more than 1.0g/cm3. 5. Mixing speed is 65rpm to reach a good mixing effect for powder. 6. Weight of the mixer is about 300kgs.   Features of 100L Horizontal Ribbon Mixer With Liquid Spray System: 1. The mixing tank is specially designed to get a better mixing effect for powder and granules. 2. 100L Horizontal Ribbon Mixer is all made of stainless steel SUS304. 3. It is equipped with a supporting frame to get a higher discharging position. Easy to collect the final product after mixing. 4. The mixing tank is smooth, easy to discharge and...

Why does the CNC bending machine adopt the forging method? With the development of society, my country's steelmaking technology has reached a certain level. At present, the common processing methods are mainly forging and casting. Castings are lower in cost than forgings. CNC bending machine molds are forged. Many people are curious about why not castings. This article will briefly describe the reasons. CNC Press brake Casting technology has a long history in my country. The overall cost of the workpiece is very low, mainly by smelting the metal into a liquid, and then pouring the liquid into a specific forming mold. After the metal liquid is cooled, a shaped casting is formed. The casting technology is to burn some steel material in a charcoal fire, and then quickly pull the red steel out and put it into an air hydraulic hammer for forging. Hydraulic bending machine blade mould The reason why CNC bending machine molds choose forging instead of casting is because casting generall...

Machining is manufacturing process that involves removing materials using cutting tools for getting rid of the unwanted materials from some workpiece and converting it into the shape you desire. A large piece of stock is used for cutting the workpiece. The large stock might be in any shape such as solid bar, flat sheet, beam or even hollow tubes. The process can also be performed on some existing part like forging or casting.In drilling process holes are created in the metal through circular cylinders. A twist drill is used for accomplishing this task. 75% of the metal cutting material is removed through the drilling operation. The drill enters the workpiece and cuts a hole which is equal to the diameter of the tool that was used for cutting the whole. A drill has a pointed end which can easily cut a hole in the work piece. D&S can offer you all kinds of drilling and tapping machine . If you need,welcome to contact

  DN50  Ceramic ball valves   with F316 body and ceramic lining were exported to Norway again to solve abrasion and corrosion problems in mining projects for our end user. Considering the corrosive working environment, the body of the ball valves are changed from carbon steel A105 to stainless steel F316. The body is fully lined with ceramic as before. The medium is corrosive mining slurry with abrasive nickel and metal particles. The end user used metal seated ball valves before, but the metal seats were worn out easily under the corrosive and abrasive working conditions. After usage of our  corrosion and abrasion  resistant ceramic ball valves , thanks to the extreme physical harness and chemical stablity, the working life is increased dramatically and the maintenance cost and shutdown time are reduced a lot. When there are corrosive fluid and abrasive solid in the same application, the corrosion and abrasion problems are hard to be solved. The abrasion p...

  Why should we pay attention to the cylinder when buying a CNC bending machine The cylinder is used to hold hydraulic oil, and the  CNC bending machine  is a kind of machine for bending sheet metal. When we use the CNC bending machine to bend the material, we must bend in the middle section. If we are bending on one side, then when the cylinder on one side touches the workpiece, the cylinder on the other side will continue downward until it touches the lower die, the two cylinders begin to pressurize. If the cylinder is working like this, one side high and the other side low, the cylinder of the CNC bending machine will soon be damaged and leak oil. Secondly, try not to choose a two-cylinder CNC bending machine, because the working life of such a CNC bending machine is too short. When the workpiece is in the middle of the  CNC bending machine  and the cylinder is on both sides, the bending of the slider is affirmative; in addition, due to the reaction force gen...